xfanta

3D-printed Gravity Gun from Half-Life 2

I made this model for my photo booth at the first Maker Faire Prague. You can print it on an ordinary 3D printer.

Michal Fanta4 min readAlso available inCS
3D-printed Gravity Gun from Half-Life 2

I designed the Gravity Gun in 2018 as the main attraction of my photo booth at the very first Maker Faire in Prague. I picked it because it isn't a typical video game weapon but an anti-gravity device. It was also a good excuse to try my first Arduino project, with servo motors and LED strips.

And of course, I've always liked the Gravity Gun from Half-Life, so why not have one at home.

The Gravity Gun on a wooden crate in the photo booth at Maker Faire Prague 2018.

72 cm, 52 different parts

Assembled, the Gravity Gun measures about 72 × 42 × 27 cm (28 × 17 × 11 in). It's made of 52 different parts. Some are printed more than once – everything on the arms three times, the long ribs six times – so 98 pieces come off the printer in the end.

The parts are split into six sub-assemblies, each put together on its own:

  • Discs – two discs with the rear grip
  • Repro case – the cover with the speaker grille
  • Case – the armoured middle section with two light covers
  • Body – translucent shells, ribs and the front ring with the claws
  • Arms – three arms with a lever mechanism
  • Side grip case – the side handle and the gauge with its needle

The arms aren't just for show. Each one is a four-bar linkage: the top and bottom levers hold the arm and its head, and when the lever turns, the arm opens. My prototype had electronics that brought the Gravity Gun to life. The download contains only the 3D-printed parts, so if you want a "working" one, you'll have to dive into an Arduino project of your own.

👉 Gravity Gun on Printables

Printing

I printed every part on an Original Prusa MK2, so they'll fit an MK3, MK4 or any other printer with a bed of similar size. The STL files come oriented for printing. Only one part needs supports, the Side Grip Case Gauge, and only a few.

I printed in grey PLA, because I planned to paint the model anyway. The translucent parts were a different matter. I didn't have orange filament at hand, so I used blue PLA and ended up with the Gravity Gun from the later part of the game, set in the Citadel. PLA or PETG, either will do.

Assembly

The hardware is standard metric: mostly M3 button head screws (ISO 7380), a few socket head cap screws (ISO 4762), plus some M4 and M6 screws and one M8. The M3 and M6 nuts sit in pockets in the parts, and a dab of hot glue keeps them there. Where there's no nut, the screw goes straight into the plastic. Each arm turns on a 623 bearing (3 × 10 × 4 mm), and the side grip on an M8 screw in a 608 bearing (8 × 22 × 7 mm).

The illustrated PDF guide comes with the download, or you can browse it comfortably at gravity-gun.com. It walks through the build one sub-assembly at a time, screw by screw, starting with the discs and the rear grip and finishing with the arms on the body.

Illustration from the guide: disc left is screwed to disc right, which first gets two M6 nuts.

The assembly takes 196 screws, 25 nuts and 4 bearings. You'll find the complete list on the model's website.

Paint and patina

The Gravity Gun in the photos isn't straight off the printer. I sprayed the parts with plastic primer, sanded them, painted them and finally weathered them to look like worn metal.

All the painted parts laid out on a blue cutting mat.

STEP files for your own electronics

Besides the STL files, the download includes STEP files: every part and every sub-assembly, this time in its original position rather than oriented for printing. They come in handy if you want to modify the model or add LEDs, servos or a speaker.

I haven't published the original electronics, because they aren't in a state I could release. That's why the holes for switches and connectors are closed in the parts, and printed dummies stand in for the servos.

Download the Gravity Gun

The model is a paid download on Printables, currently on sale for $9 instead of $29. At gravity-gun.com you can explore it in 3D before you buy.

The Gravity Gun holding a circular saw blade between its arms, in the 3D viewer at gravity-gun.com.
Written by
Michal Fanta

I design 3D models in Onshape, print them on Prusa 3D printers, and build websites and apps.

Comments

No comments yet. Be the first.

Your name and comment are published. Your email isn’t; I only use it to write back. Want a comment taken down? Write to apps@xfanta.com.

Follow what I make

New apps, new models and new posts — pick the channel you already use.